GV/ F Series Super Duty Moulder
  • FEATURE
  • SPECS
  • The full safely enclosure cover as chips guard and helps to reduce noises.
  • Table surface is hard-chrome plated for maximum wear resistance.
  • All manually adjusted turning parts are housed in dry hearings for oil-free lubrication.
  • One-piece, cast iron machine frame and table is especially normalization heat treated for maximum stability and rigidity.
  • The smooth initial feeding of the stock is achieved by the independently powered infeed rollers.
  • All spindles are precision constructed and especially heat treated to provide maximum cutting stability and permanent accuracy.
  • Higher spindle speeds are available upon request.
  • Fence adjusted is quickly accomplished by a quick-setting lever.
  • The Three independent section pneumatic pressure for the infeed rollers, in-process rollers and outfeed rollers can be set with individual pressure allowing for consistent feeding results and outstanding effect.
  • The entire motion controls of the machine are centralized on the control panel for convenient operations.
  • All control levers for the spindles are located at the front of the machine for convenient adjustment.
  • Each spindle is provided with a mechanical digital read out, that giving accurate adjustment.
  • The pressure roller for short stork can be fast raised, providing maximum convenient while cutter changing or setup.
  • Separate adjustment of vertical spindle and insert table, permits the table to be position extremely close to the cutter head for added cutting stability.
  • The front pressure plate features draw-back performance. Which fully avoid damage on cutters caused by an over-height work piece.
  • The rear pressure plate provides extremely uniform molding pressure for outstanding parallelism accuracy of machining.
  • An individual motor drives each spindle and is separately mounted to eliminate spindle chattering during high speed running.
  • The roller in the infeed table is powered, providing a smooth feeding effect for the tough stock.
  • The spindles are lubricated by the centralized lubrication system for convenience.
SpecificationsGV/ F SERIES
Capacity Moulding Spindle Number (Min. ~ Max.) 4 ~ 9
Working Width 5/7" ~ 9" (18 ~ 230 mm)
Working Thickness 2/9" ~ 6-2/7" (6 ~ 160 mm)
Min. Working Length 9-4/9" (240 mm)
Feed Speed 7 ~ 36 m/ min
Motor 1st Bottom Horizontal Spindle 7.5 HP
2nd Right Vertical Spindle 7.5 HP
3rd Left Vertical Spindle 10 HP
Top Horizontal Spindle 10 HP
Bottom Horizontal Spindle 10 HP
U Spindle (OPT) 7.5 HP
Elevation  1 HP
Spindle

 

Spindle Cutting Speed 6200 RPM
Spindle Diameter Ø1-4/7" (40 mm)
Adjustment Range of Vertical Spindle 3-1/7" (80 mm)
Adjustment Range of Horizontal Spindle 1-3/8" (35 mm)
Cutting Circles 1st Bottom Horizontal Spindle Ø4" (100 mm) ~ Ø7" (180 mm)
Right Vertical Spindle Ø4-1/3" (110 mm) ~ Ø9-5/6" (250 mm)
Left Vertical Spindle Ø4-1/3" (110 mm) ~ Ø9-5/6" (250 mm)
1st Top Horizontal Spindle Ø4-1/3" (110 mm) ~ Ø9-5/6" (250 mm)
2nd Bottom Horizontal Spindle Ø4-1/3" (110 mm) ~ Ø9-5/6" (250 mm)
All Other Dust Outlet Diameter 5½" (140 mm)
Infeed Table 2M
Feed Roller Diameter 5½" (140 mm)
Pneumatic Pressure for Feed Roller, Max 6 bar (87 psi)
Adjustment Range for infeed Table and edge-jointing Fence 2/5" (10 mm)
Top